Convert Power Point into a Macromedia Flash MX

To convert Power Point into a Macromedia Flash MX takes several steps, among others:
• Open an existing PowerPoint slides on your computer harddisc.
• Click File> Save As> Save as type to select windows metafile.

• When asked if you want to save all the slides, then the answer is that each slide (every slide).
• Open Macromedia Flash MX> File> Import> Import to Stage> select slide. Wmf to be imported> open.
• After that we can edit our liking.

In changing the Power Point into a Macromedia Flash there are some disadvantages such as we have to rearrange the display Power Point in Flash and very inefficient when Slide to change too many.

Making USB Power Injector with Auto Power-ON

Some time ago, in my post entitled Making USB or USB Power Injector Power injector there are some who asked about his USB Power injector that is not equipped with Automatic System PSU so the user must turn on / turn circuit manually after Jack USB plugged in USB connector CPU. For those following my posts the development of USB Power Injector before.

In this series are equipped with Automatic PSU so that Controller Device (Wi-fi/Modem) will automatically turn on as soon Jack USB Power injector is plugged into the USB socket CPU. Here I made ​​2 model series, the first to use both MOSFET and Bipolar Transistor regular use. I accidentally made ​​two series so that those who have difficulty obtaining MOSFETs can make alternative circuit with components Bipolar transistors are more easily available in the market. Here's Development Series Block Diagram USB Power injector.

Automatic circuit Controller PSU put under so you had to make a USB Power Injector earlier versions do not need to change the settings at the top of the stabilizer. In addition to the system as it does not need extra cables to the top but just use a UTP cable that already exists.

Automatic circuit PSU Controller to USB Power injector MOSFET version:

Automatic circuit PSU Controller to USB Power injector for Bipolar Transistor version:

As for the components and the MOSFET transistors structure and its symbols and legs you can see the Data Sheet Components.
Data Sheet USB Components Injector

Foot structure component is a standard arrangement of the Data Sheet. Especially for C1815 Transistor foot structure, PN100, 2N3904 S8050 and you should re-check using AVO-meter arrangement because sometimes he does not conform Data Sheet.
With the additional circuit device (Wi-fi/Modem) lights / turn on automatically when Jeck USB Power Injector is plugged into the CPU socket and the USB device will automatically shut off when Jack is released so you do not need to manually turn on the device.
So hopefully the development of USB Power Injector helpful.  

How to make a USB extender. Ingredients:

1. ordinary USB cable, standard aja yg 1 m or 0.5m.
2. Wired LAN / UTP cabling for the network.


Step 1: The USB cable is tested before use USB flash disk in the computer, it is still functioning or not. If it is OK, cut into 2 parts. There are usually red, black, and white, green. Red and black are usually for 5V supply voltages. Green white is usually a USB data cable.

Step 2: Cut and peel the ends of the LAN cable. Of the LAN cable have 8 colors. Of 8 LAN cable ends earlier, merge several pairs that stayed 4 LAN cable ends.

* Combined with orange orange white wires (2 wires so 1)
* Green white cable (1 cable)
* Green cable (1 cable)
* Combination of blue and white wires, blue, white, brown, brown (4 wires so 1)

Step 3: Connect the ends of the USB cable to the LAN cable ends as follows:

* White orange - orange (2 wires) (UTP) = red (USB)
* White green (1 cable) (UTP) = white (USB)
* Green (1 cable) (UTP) = green (USB)
* White-blue, blue, white, brown, brown (4 wires) (UTP) = black (USB)

Make sure each connection in isolation use masking tape to Rapet

Step 4, the most important: set speed USB port on the computer motherboard to be USB 1.1, not USB 2.0. USB 1.1 has a maximum speed of 10Mbps, so more reliable for long-distance attractiveness compared to USB 2.0.

 

Mikrotik Router Hotspot Billing Integration Setting

Setting Mikrotik Router Hotspot Billing integration is straightforward that, through mikrotik installed correctly, run the application "Winbox Loader" so that you can configure Mikrotik Router from the Windows desktop to easily and quickly without having to memorize the command line Mikrotik. After double click the Winbox application will appear as follows:

After that Click ... it would appear MAC Address Mikrotik current in this case double-click the Mac Address 00:0 B: CD: 64: D9: 22 and fill in the user admin and the default password is blank and then click "Connect"

IP ==> Address ListClick the plus sign | + | then the "Address" then enter the desired IP number eg 192.168.1.110/24 (slash 24 means later will automatically fill in the Network and Broadcast). Then in the "Interface" select ether1 ether1 which will be connected to the modem / ISP.
 IP ==> Route ListClick the plus sign | + | then on "Gateway" fill your Gateway IP, eg 192.168.1.1 Then click "OK"
 New TerminalThen will appear the following console and then do a ping to your Internet Gateway, type ping 192.168.1.1 If successful it will look like the image below and it means a network of Mikrotik to Gateway / modem connected to normal.
 Interface ==> Interface ListIt is to see the interface or the Ethernet card which is active (to connect to the network) is in position "Tx" and "Rx" will display traffic xxx bps. In case this is ether1 is connected to a LAN network
 IP ==> DNSThen click "Settings" in the "Primary DNS" fill DNS1 eg 202.134.1.10 and the "Secondary DNS" fill DNS2 eg 202.134.0.155 and if after click "OK"
 New TerminalPerform the testing ping out to the internet eg to google.com by typing ping google.com if results like this then your internet connection is connect.
 IP ==> == Hotspot> Hotspot SetupIn the "Hotspot Interface" select ether which want to make a hotspot, in this case, and if there is ether3 wireless LAN antenna you choose. Then click "Next"
 In the "Local Address of Network" is your Hotspot Gateway, and then click "Next"
 In the "Address Pool of Network" is a DHCP IP Range that will be provided to the user hotspot. You can specify how many want in terms of the IP range is from 10.5.50.2 s / d 10.5.50.254 then click "Next"
 In the "Select Certificate" select "none" and then click "Next"
 In the "IP Address of SMTP Server" leave blank and click "Next"
 In the "DNS Servers" already filled your DNS properly and immediately wrote click "Next"
 In the "DNS Name" leave it blank and click "Next"
 Then just click "Next"
 When finished it will display the following dialog box and then click "OK"
 Then continue with the configuration in order to connect to Hotspot Mikrotik Hotspot Billing software as follows:IP ==> Hotspot ==> Server Profiles ==> hsprof1 (2x click)From the "General" tab to move to the tab "Login" and then un-check (uncheck) the "Cookies" and then click "Apply"
 Then move to the tab "Radius" and un-check (uncheck) the "Use RADIUS" then click "Apply" and then click "OK"
 RadiusClick the plus sign | + | and on the General tab tick hotspot service later in the "Address" enter the IP Address Billing Hotspot radius server (Linux PC) and "Secret" secret id ie 123,457,890 fill as you fill in Linux, then if finished click "OK"
 In order for User Login Page Hotspot Billing Hotspot login page appears as shown below
 IP ==> == HotSpot> Walled GardenClick the plus sign | + | and to "Action = allow" select "Dst. Address "enter the IP number Hotspot Billing server, for example 192.168.1.10 and then click" OK "
 When finished upload your files into mikrotik already configured by software Hotspot Billing TeamThe next step in order to Hotspot Billing integrates with Mikrotik Router, you need to login to Billing Hotspot Manager. Enter your username, password, and security code correctly as shown below.
 After a successful entry into the Hotspot Billing Manager, log == Preferences Menu> Settings Service ==> Select / var / www / html / config.client.php then click "Edit" and when finished click "Save"$ IpServer = "192.168.1.2"; ==> enter the IP Server Hotspot Billing$ IpMikrotik = "192.168.1.10"; ==> enter the IP Router Mikrotik$ UserMikrotik = "admin"; ==> insert a user name Mikrotik Router$ PassMikrotik = "admin"; ==> enter password Mikrotik Router
 If you can not be saved into Konsole as root on Linux and type the command chmod 775 / var / www / html / config.client.phpLog Preferences ==> Settings Service ==> Select the / etc / raddb / clients.conf then click the "Edit" pull scroll to the bottom line and add the following four lines of command and when finished click "Save"client 192.168.1.2 ==> fill in the IP Router Mikrotiksecret = 123457890 ==> insert appropriate RADIUS secret Mikrotikshortname = proxy ==> insert a label with the name 'proxy'
 Log Preferences ==> Settings Service ==> Select the / etc / raddb / naslist then click "Edit"
 If you can not be saved into Konsole as root on Linux and type the command chmod 775 / etc / raddb / naslist